思科认证基础知识:Switching命令

时间:2020-11-14 18:55:46 思科认证 我要投稿

2016年思科认证基础知识:Switching命令大全

  学习思科认证,必须知道Switching命令,那么Switching的基本命令有哪些呢?下面跟yjbys小编一起来看看吧!

2016年思科认证基础知识:Switching命令大全

  1. 在基于IOS的交换机上设置主机名/系统名:

  switch(config)# hostname hostname

  在基于CLI的交换机上设置主机名/系统名:

  switch(enable) set system name name-string

  2.在基于IOS的交换机上设置登录口令:

  switch(config)# enable password level 1 password

  在基于CLI的交换机上设置登录口令:

  switch(enable) set password

  switch(enable) set enalbepass

  3.在基于IOS的交换机上设置远程访问:

  switch(config)# interface vlan 1

  switch(config-if)# ip address ip-address netmask

  switch(config-if)# ip default-gateway ip-address

  在基于CLI的交换机上设置远程访问:

  switch(enable) set interface sc0 ip-address netmask broadcast-address

  switch(enable) set interface sc0 vlan

  switch(enable) set ip route default gateway

  4.在基于IOS的交换机上启用和浏览CDP信息:

  switch(config-if)# cdp enable

  switch(config-if)# no cdp enable

  为了查看Cisco邻接设备的CDP通告信息:

  switch# show cdp interface [type modle/port]

  switch# show cdp neighbors [type module/port] [detail]

  在基于CLI的交换机上启用和浏览CDP信息:

  switch(enable) set cdp {enable|disable} module/port

  为了查看Cisco邻接设备的CDP通告信息:

  switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail]

  5.基于IOS的交换机的端口描述:

  switch(config-if)# description description-string

  基于CLI的交换机的端口描述:

  switch(enable)set port name module/number description-string

  6.在基于IOS的交换机上设置端口速度:

  switch(config-if)# speed{10|100|auto}

  在基于CLI的交换机上设置端口速度:

  switch(enable) set port speed moudle/number {10|100|auto}

  switch(enable) set port speed moudle/number {4|16|auto}

  7.在基于IOS的交换机上设置以太网的链路模式:

  switch(config-if)# duplex {auto|full|half}

  在基于CLI的交换机上设置以太网的链路模式:

  switch(enable) set port duplex module/number {full|half}

  8.在基于IOS的交换机上配置静态VLAN:

  switch# vlan database

  switch(vlan)# vlan vlan-num name vla

  switch(vlan)# exit

  switch# configure teriminal

  switch(config)# interface interface module/number

  switch(config-if)# switchport mode access

  switch(config-if)# switchport access vlan vlan-num

  switch(config-if)# end

  在基于CLI的交换机上配置静态VLAN:

  switch(enable) set vlan vlan-num [name name]

  switch(enable) set vlan vlan-num mod-num/port-list

  9. 在基于IOS的交换机上配置VLAN中继线:

  switch(config)# interface interface mod/port

  switch(config-if)# switchport mode trunk

  switch(config-if)# switchport trunk encapsulation {isl|dotlq}

  switch(config-if)# switchport trunk allowed vlan remove vlan-list

  switch(config-if)# switchport trunk allowed vlan add vlan-list

  在基于CLI的交换机上配置VLAN中继线:

  switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate]

  Vlan-range [isl|dotlq|dotl0|lane|negotiate]

  10.在基于IOS的交换机上配置VTP管理域:

  switch# vlan database

  switch(vlan)# vtp domain domain-name

  在基于CLI的交换机上配置VTP管理域:

  switch(enable) set vtp [domain domain-name]

  11.在基于IOS的交换机上配置VTP 模式:

  switch# vlan database

  switch(vlan)# vtp domain domain-name

  switch(vlan)# vtp {sever|cilent|transparent}

  switch(vlan)# vtp password password

  在基于CLI的交换机上配置VTP 模式:

  switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent }][password password]

  12. 在基于IOS的交换机上配置VTP版本:

  switch# vlan database

  switch(vlan)# vtp v2-mode

  在基于CLI的交换机上配置VTP版本:

  switch(enable) set vtp v2 enable

  13. 在基于IOS的交换机上启动VTP剪裁:

  switch# vlan database

  switch(vlan)# vtp pruning

  在基于CL I 的交换机上启动VTP剪裁:

  switch(enable) set vtp pruning enable

  14.在基于IOS的交换机上配置以太信道:

  switch(config-if)# port group group-number [distribution {source|destination}]

  在基于CLI的交换机上配置以太信道:

  switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto}

  15.在基于IOS的交换机上调整根路径成本:

  switch(config-if)# spanning-tree [vlan vlan-list] cost cost

  在基于CLI的交换机上调整根路径成本:

  switch(enable) set spantree portcost moudle/port cost

  switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list]

  16.在基于IOS的交换机上调整端口ID:

  switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority

  在基于CLI的交换机上调整端口ID:

  switch(enable) set spantree portpri {mldule/port}priority

  switch(enable) set spantree portvlanpri {module/port}priority [vlans]

  17. 在基于IOS的交换机上修改STP时钟:

  switch(config)# spanning-tree [vlan vlan-list] hello-time seconds

  switch(config)# spanning-tree [vlan vlan-list] forward-time seconds

  ` switch(config)# spanning-tree [vlan vlan-list] max-age seconds

  在基于CLI的交换机上修改STP时钟:

  switch(enable) set spantree hello interval[vlan]

  switch(enable) set spantree fwddelay delay [vlan]

  switch(enable) set spantree maxage agingtiame[vlan]

  18. 在基于IOS的'交换机端口上启用或禁用Port Fast 特征:

  switch(config-if)#spanning-tree portfast

  在基于CLI的交换机端口上启用或禁用Port Fast 特征:

  switch(enable) set spantree portfast {module/port}{enable|disable}

  19. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征:

  switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second]

  在基于CLI的交换机端口上启用或禁用UplinkFast 特征:

  switch(enable) set spantree uplinkfast {enable|disable}[rate update-rate] [all-protocols off|on]

  20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,然后使用下列命令: switch(config)# cluster enable cluster-name

  21. 为了从一条中继链路上删除VLAN,可使用下列命令:

  switch(enable) clear trunk module/port vlan-range

  22. 用show vtp domain 显示管理域的VTP参数.

  23. 用show vtp statistics显示管理域的VTP参数.

  24. 在Catalyst交换机上定义TrBRF的命令如下:

  switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp {ieee|ibm}]

  25. 在Catalyst交换机上定义TrCRF的命令如下:

  switch (enable) set vlan vlan-num [name name] type trcrf

  {ring hex-ring-num|decring decimal-ring-num} parent vlan-num

  26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口:

  switch(enable) set vlan vlan-num mod-num/port-num

  27. 命令show spantree显示一个交换机端口的STP状态.

  28. 配置一个ELAN的LES和BUS,可以使用下列命令:

  ATM (config)# interface atm number.subint multioint

  ATM(config-subif)# lane serber-bus ethernet elan-name

  29. 配置LECS:

  ATM(config)# lane database database-name

  ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address

  ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address

  ATM(lane-config-databade)# name …

  30. 创建完数据库后,必须在主接口上启动LECS.命令如下:

  ATM(config)# interface atm number

  ATM(config-if)# lane config database database-name

  ATM(config-if)# lane config auto-config-atm-address

  31. 将每个LEC配置到一个不同的ATM子接口上.命令如下:

  ATM(config)# interface atm number.subint multipoint

  ATM(config)# lane client ethernet vlan-num elan-num

  32. 用show lane server 显示LES的状态.

  33. 用show lane bus显示bus的状态.

  34. 用show lane database显示LECS数据库可内容.

  35. 用show lane client显示LEC的状态.

  36. 用show module显示已安装的模块列表.

  37. 用物理接口建立与VLAN的连接:

  router# configure terminal

  router(config)# interface media module/port

  router(config-if)# description description-string

  router(config-if)# ip address ip-addr subnet-mask

  router(config-if)# no shutdown

  38. 用中继链路来建立与VLAN的连接:

  router(config)# interface module/port.subinterface

  router(config-ig)# encapsulation[isl|dotlq] vlan-number

  router(config-if)# ip address ip-address subnet-mask

  39. 用LANE 来建立与VLAN的连接:

  router(config)# interface atm module/port

  router(config-if)# no ip address

  router(config-if)# atm pvc 1 0 5 qsaal

  router(config-if)# atm pvc 2 0 16 ilni

  router(config-if)# interface atm module/port.subinterface multipoint

  router(config-if)# ip address ip-address subnet-mask

  router(config-if)# lane client ethernet elan-num

  router(config-if)# interface atm module/port.subinterface multipoint

  router(config-if)# ip address ip-address subnet-name

  router(config-if)# lane client ethernet elan-name

  router(config-if)# …

  40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行:

  router(config)# ip routing

  router(config)# router ip-routing-protocol

  router(config-router)# network ip-network-number

  router(config-router)# network ip-network-number

  41. 配置默认路由:

  switch(enable) set ip route default gateway

  42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令:

  router(config)# interface interface number

  router(config-if)# mls rp vlan-id vlan-id-num

  43. 在路由处理器启用MLSP:

  router(config)# mls rp ip

  44. 为了把一个外置的路由处理器接口和交换机安置在同一个VTP域中:

  router(config)# interface interface number

  router(config-if)# mls rp vtp-domain domain-name

  45. 查看指定的VTP域的信息:

  router# show mls rp vtp-domain vtp domain name

  46. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令:

  router(config-if)#mls rp management-interface

  47. 要检验MLS-RP的配置情况:

  router# show mls rp

  48. 检验特定接口上的MLS配置:

  router# show mls rp interface interface number

  49. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表:

  set mls flow [destination|destination-source|full]

  50. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令:

  router(config)# mls rp ip input-acl

  51. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令:

  switch(enable) set mls enable

  52. 若想改变老化时间的值,可在特权模式下输入以下命令:

  switch(enable) set mls agingtime agingtime

  53. 设置快速老化:

  switch(enable) set mls agingtime fast fastagingtime pkt_threshold

  54. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定:

  switch(enable) show mls include

  55. 显示MLS高速缓存记录:

  switch(enable) show mls entry

  56. 用命令show in arp显示ARP高速缓存区的内容。

  57. 要把路由器配置为HSRP备份组的成员,可以在接口配置模式下使用下面的命令:

  router(config-if)# standby group-number ip ip-address

  58. 为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下:

  router(config-if)# standy group-number preempt

  59. 访问时间和保持时间参数是可配置的:

  router(config-if)# standy group-number timers hellotime holdtime

  60. 配置HSRP跟踪:

  router(config-if)# standy group-number track type-number interface-priority

  61. 要显示HSRP路由器的状态:

  router# show standby type-number group brief

  62. 用命令show ip igmp确定当选的查询器。

  63. 启动IP组播路由选择:

  router(config)# ip muticast-routing

  64. 启动接口上的PIM:

  dalllasr1>(config-if)# ip pim {dense-mode|sparse-mode|sparse-dense-mode}

  65. 启动稀疏-稠密模式下的PIM:

  router# ip multicast-routing

  router# interface type number

  router# ip pim sparse-dense-mode

  66. 核实PIM的配置:

  dallasr1># show ip pim interface[type number] [count]

  67. 显示PIM邻居:

  dallasr1># show ip neighbor type number

  68. 为了配置RP的地址,命令如下:

  dallasr1># ip pim rp-address ip-address [group-access-list-number][override]

  69. 选择一个默认的RP:

  dallasr1># ip pim rp-address

  通告RP和它所服务的组范围:

  dallasr1># ip pim send-rp-announce type number scope ttl group-list access-list-number

  为管理范围组通告RP的地址:

  dallasr1># ip pim send-rp-announce ethernet0 scope 16 group-list1

  dallasr1># access-list 1 permit 266.0.0.0 0.255.255.255

  设定一个RP映像代理:

  dallasr1># ip pim send-rp-discovery scope ttl

  核实组到RP的映像:

  dallasr1># show ip pim rp mapping

  dallasr1># show ip pim rp [group-name|group-address] [mapping]

  70. 在路由器接口上用命令ip multicast ttl-threshold ttl-value设定TTL阀值:

  dallasr1>(config-if)# ip multicast ttl-threshold ttl-value

  71. 用show ip pim neighbor显示PIM邻居表。

  72. 显示组播通信路由表中的各条记录:

  dallasr1>show ip mroute [group-name|group-address][scoure][summary][count][active kbps]

  73. 要记录一个路由器接受和发送的全部IP组播包:

  dallasr1> #debug ip mpacket [detail] [access-list][group]

  74. 要在CISCO路由器上配置CGMP:

  dallasr1>(config-if)# ip cgmp

  75.配置一个组播路由器,使之加入某一个特定的组播组:

  dallasr1>(config-if)# ip igmp join-group group-address

  76. 关闭 CGMP:

  dallasr1>(config-if)# no ip cgmp

  77. 启动交换机上的CGMP:

  dallasr1>(enable) set cgmp enable

  78. 核实Catalyst交换机上CGMP的配置情况:

  catalystla1>(enable) show config

  set prompt catalystla1>

  set interface sc0 192.168.1.1 255.255.255.0

  set cgmp enable

  79. CGMP离开的设置:

  Dallas_SW(enable) set cgmp leave

  80. 在Cisco设备上修改控制端口密码:

  R1(config)# line console 0

  R1(config-line)# login

  R1(config-line)# password Lisbon

  R1(config)# enable password Lilbao

  R1(config)# login local

  R1(config)# username student password cisco

  81. 在Cisco设备上设置控制台及vty端口的会话超时:

  R1(config)# line console 0

  R1(config-line)# exec-timeout 5 10

  R1(config)# line vty 0 4

  R1(config-line)# exec-timeout 5 2

  82. 在Cisco设备上设定特权级:

  R1(config)# privilege configure level 3 username

  R1(config)# privilege configure level 3 copy run start

  R1(config)# privilege configure level 3 ping

  R1(config)# privilege configure level 3 show run

  R1(config)# enable secret level 3 cisco

  83. 使用命令privilege 可定义在该特权级下使用的命令:

  router(config)# privilege mode level level command

  84. 设定用户特权级:

  router(config)# enable secret level 3 dallas

  router(config)# enable secret san-fran

  router(config)# username student password cisco

  85. 标志设置与显示:

  R1(config)# banner motd ‘unauthorized access will be prosecuted!’

  86. 设置vty访问:

  R1(config)# access-list 1 permit 192.168.2.5

  R1(config)# line vty 0 4

  R1(config)# access-class 1 in

  87. 配置HTTP访问:

  Router3(config)# access-list 1 permit 192.168.10.7

  Router3(config)# ip http sever

  Router3(config)# ip http access-class 1

  Router3(config)# ip http authentication local

  Router3(config)# username student password cisco

  88. 要启用HTTP访问,请键入以下命令:

  switch(config)# ip http sever

  89. 在基于set命令的交换机上用setCL1启动和核实端口安全:

  switch(enable) set port security mod_num/port_num…enable mac address

  switch(enable) show port mod_num/port_num

  在基于CiscoIOS命令的交换机上启动和核实端口安全:

  switch(config-if)# port secure [mac-mac-count maximum-MAC-count]

  switch# show mac-address-table security [type module/port]

  90. 用命令access-list在标准通信量过滤表中创建一条记录:

  Router(config)# access-list access-list-number {permit|deny} source-address [source-address]

  91. 用命令access-list在扩展通信量过滤表中创建一条记录:

  Router(config)# access-list access-list-number {permit|deny{protocol|protocol-keyword}}{source source-wildcard|any}{destination destination-wildcard|any}[protocol-specific options][log]

  92. 对于带内路由更新,配置路由更新的最基本的命令格式是:

  R1(config-router)#distribute-list access-list-number|name in [type number]

  93. 对于带外路由更新,配置路由更新的最基本的命令格式是:

  R1(config-router)#distribute-list access-list-number|name out [interface-name] routing-process| autonomous-system-number

  94. set snmp命令选项:

  set snmp community {read-only|ready-write|read-write-all}[community_string]

  95. set snmp trap 命令格式如下:

  set snmp trap {enable|disable}

  [all|moudle|classis|bridge|repeater| auth|vtp|ippermit|vmps|config|entity|stpx]

  set snmp trap rvcr_addr rcvr_community

  96. 启用SNMP chassis 陷阱:

  Console>(enable) set snmp trap enable chassis

  97. 启用所有SNMP chassis 陷阱:

  Console>(enable) set snmp trap enable

  98. 禁用SNMP chassis 陷阱:

  Console>(enable) set snmp trap disable chassis

  99. 给SNMP陷阱接收表加一条记录:

  Console>(enable) set snmp trap 192.122.173.42 public

  100. show snmp 输出结果。

  101. 命令set snmp rmon enable 的输出结果。

  102. 显示SPAN信息:

  Consile> show span

【2016年思科认证基础知识:Switching命令大全】相关文章:

1.思科认证基础:Switching命令大全

2.2016年思科认证基础:Switching 命令大全

3.思科最实用的技术命令大全

4.思科认证高级认证

5.2016年思科认证基础:解决网吧故障DOS命令

6.思科交换机基本配置命令大全

7.思科认证考试认证体系

8.思科认证级别