思科交换机基本配置命令大全(3)

时间:2018-04-04 编辑:少芬 手机版

  switch(config-if)# switchport mode access

  switch(config-if)# switchport access vlan vlan-num

  switch(config-if)# end

  在基于CLI的交换机上配置静态VLAN:

  switch(enable) set vlan vlan-num [name name]

  switch(enable) set vlan vlan-num mod-num/port-list

  9. 在基于IOS的交换机上配置VLAN中继线:

  switch(config)# interface interface mod/port

  switch(config-if)# switchport mode trunk

  switch(config-if)# switchport trunk encapsulation {isl|dotlq}

  switch(config-if)# switchport trunk allowed vlan remove vlan-list

  switch(config-if)# switchport trunk allowed vlan add vlan-list

  在基于CLI的交换机上配置VLAN中继线:

  switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate]

  Vlan-range [isl|dotlq|dotl0|lane|negotiate]

  10.在基于IOS的交换机上配置VTP管理域:

  switch# vlan database

  switch(vlan)# vtp domain domain-name

  在基于CLI的交换机上配置VTP管理域:

  switch(enable) set vtp [domain domain-name]

  11.在基于IOS的交换机上配置VTP 模式:

  switch# vlan database

  switch(vlan)# vtp domain domain-name

  switch(vlan)# vtp {sever|cilent|transparent}

  switch(vlan)# vtp password password

  在基于CLI的交换机上配置VTP 模式:

  switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent }][password password]

  12. 在基于IOS的交换机上配置VTP版本:

  switch# vlan database

  switch(vlan)# vtp v2-mode

  在基于CLI的交换机上配置VTP版本:

  switch(enable) set vtp v2 enable

  13. 在基于IOS的交换机上启动VTP剪裁:

  switch# vlan database

  switch(vlan)# vtp pruning

  在基于CL I 的交换机上启动VTP剪裁:

  switch(enable) set vtp pruning enable

  14.在基于IOS的交换机上配置以太信道:

  switch(config-if)# port group group-number [distribution {source|destination}]

  在基于CLI的交换机上配置以太信道:

  switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto}

  15.在基于IOS的交换机上调整根路径成本:

  switch(config-if)# spanning-tree [vlan vlan-list] cost cost

  在基于CLI的交换机上调整根路径成本:

  switch(enable) set spantree portcost moudle/port cost

  switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list]

  16.在基于IOS的交换机上调整端口ID:

  switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority

  在基于CLI的交换机上调整端口ID:

  switch(enable) set spantree portpri {mldule/port}priority

  switch(enable) set spantree portvlanpri {module/port}priority [vlans]

  17. 在基于IOS的交换机上修改STP时钟:

  switch(config)# spanning-tree [vlan vlan-list] hello-time seconds

  switch(config)# spanning-tree [vlan vlan-list] forward-time seconds

  ` switch(config)# spanning-tree [vlan vlan-list] max-age seconds

  在基于CLI的交换机上修改STP时钟:

  switch(enable) set spantree hello interval[vlan]

  switch(enable) set spantree fwddelay delay [vlan]

  switch(enable) set spantree maxage agingtiame[vlan]

  18. 在基于IOS的交换机端口上启用或禁用Port Fast 特征:

  switch(config-if)#spanning-tree portfast

  在基于CLI的交换机端口上启用或禁用Port Fast 特征:

  switch(enable) set spantree portfast {module/port}{enable|disable}

  19. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征:

  switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second]

  在基于CLI的交换机端口上启用或禁用UplinkFast 特征:

  switch(enable) set spantree uplinkfast {enable|disable}[rate update-rate] [all-protocols off|on]

  20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,然后使用下列命令: switch(config)# cluster enable cluster-name

  21. 为了从一条中继链路上删除VLAN,可使用下列命令:

  switch(enable) clear trunk module/port vlan-range

  22. 用show vtp domain 显示管理域的VTP参数.

  23. 用show vtp statistics显示管理域的VTP参数.

  24. 在Catalyst交换机上定义TrBRF的命令如下:

  switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp {ieee|ibm}]

  25. 在Catalyst交换机上定义TrCRF的命令如下:

  switch (enable) set vlan vlan-num [name name] type trcrf

  {ring hex-ring-num|decring decimal-ring-num} parent vlan-num

  26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口:

  switch(enable) set vlan vlan-num mod-num/port-num

  27. 命令show spantree显示一个交换机端口的STP状态.

  28. 配置一个ELAN的LES和BUS,可以使用下列命令:

  ATM (config)# interface atm number.subint multioint

  ATM(config-subif)# lane serber-bus ethernet elan-name

  29. 配置LECS:

  ATM(config)# lane database database-name

  ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address

  ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address

  ATM(lane-config-databade)# name …

  30. 创建完数据库后,必须在主接口上启动LECS.命令如下:

  ATM(config)# interface atm number

  ATM(config-if)# lane config database database-name

  ATM(config-if)# lane config auto-config-atm-address

  31. 将每个LEC配置到一个不同的ATM子接口上.命令如下:

  ATM(config)# interface atm number.subint multipoint

  ATM(config)# lane client ethernet vlan-num elan-num

  32. 用show lane server 显示LES的状态.

  33. 用show lane bus显示bus的状态.

  34. 用show lane database显示LECS数据库可内容.

  35. 用show lane client显示LEC的状态.

  36. 用show module显示已安装的模块列表.

  37. 用物理接口建立与VLAN的连接:

  router# configure terminal

  router(config)# interface media module/port

  router(config-if)# description description-string

  router(config-if)# ip address ip-addr subnet-mask

  router(config-if)# no shutdown

  38. 用中继链路来建立与VLAN的连接:

  router(config)# interface module/port.subinterface

  router(config-ig)# encapsulation[isl|dotlq] vlan-number

  router(config-if)# ip address ip-address subnet-mask

  39. 用LANE 来建立与VLAN的连接:

  router(config)# interface atm module/port

  router(config-if)# no ip address

  router(config-if)# atm pvc 1 0 5 qsaal

  router(config-if)# atm pvc 2 0 16 ilni

  router(config-if)# interface atm module/port.subinterface multipoint

  router(config-if)# ip address ip-address subnet-mask

  router(config-if)# lane client ethernet elan-num

  router(config-if)# interface atm module/port.subinterface multipoint

  router(config-if)# ip address ip-address subnet-name

  router(config-if)# lane client ethernet elan-name

  router(config-if)# …

  40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行:

  router(config)# ip routing

  router(config)# router ip-routing-protocol

  router(config-router)# network ip-network-number

  router(config-router)# network ip-network-number

  41. 配置默认路由:

  switch(enable) set ip route default gateway

  42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令:

  router(config)# interface interface number

  router(config-if)# mls rp vlan-id vlan-id-num

  43. 在路由处理器启用MLSP:

  router(config)# mls rp ip

  44. 为了把一个外置的路由处理器接口和交换机安置在同一个VTP域中:

  router(config)# interface interface number

  router(config-if)# mls rp vtp-domain domain-name

  45. 查看指定的VTP域的信息:

  router# show mls rp vtp-domain vtp domain name

  46. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令:

  router(config-if)#mls rp management-interface

  47. 要检验MLS-RP的配置情况:

  router# show mls rp

  48. 检验特定接口上的MLS配置:

  router# show mls rp interface interface number

  49. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表:

  set mls flow [destination|destination-source|full]

  50. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令:

  router(config)# mls rp ip input-acl

  51. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令:

  switch(enable) set mls enable

  52. 若想改变老化时间的值,可在特权模式下输入以下命令:

  switch(enable) set mls agingtime agingtime

  53. 设置快速老化:

  switch(enable) set mls agingtime fast fastagingtime pkt_threshold

  54. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定:

  switch(enable) show mls include

  55. 显示MLS高速缓存记录:

  switch(enable) show mls entry

  56. 用命令show in arp显示ARP高速缓存区的内容。

  57. 要把路由器配置为HSRP备份组的成员,可以在接口配置模式下使用下面的命令:

  router(config-if)# standby group-number ip ip-address

  58. 为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下:

  router(config-if)# standy group-number preempt


更多思科交换机相关文章:

思科交换机基本配置命令大全(3)相关推荐